Check the listing for details. Code Alarm CRCX3 Replacement Remote Transmitter Key FOB FCC ID ELVATKC H7110AS02. Condition: New. Listed at 34.10 USD. Subaru keyless remote H7110AS020 key fob code alarm FCC ID GOH-M24 dealer installed codealarm system transmitter control Code Alarm CRCX3 replacement keyfob - pre-owned 2 button 203no This is for one (1) replacement remote for your Subaru dealer installed RKE (remote keyless entry) system. You will receive one of the remotes pictured. This is ONE (1) Dealer Installed Original Equipment O.E.M. keyless remote control transmitter. This remote was used by many new car dealerships as a dealer installed remote. This means that if a car was not built with factory keyless entry but when the car was ordered as new the customer wanted keyless entry or alarm the dealer ship would install the system that uses this remote. This remote could come with many logos (i.e. ford, Chrysler, Mitsubishi, Subaru, etc...) but they are all made by Code Alarm. The remote comes with programming instructions to make the system accept the remote. Compatibility 1: FCC ID/Part number MUST match with original. Compatibility 2: Original MUST look identical with same buttons. _________________________________ Programming Instructions: Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. To program transmitters: 1.Turn the ignition ON. 2.Press and hold the valet/override button. 3.Within 10 seconds the system will chirp/flash the parking lights (3) three times, release the button. 4.Press Button 1 of each transmitter you wish to program. The system will respond with 1 chirp for each accepted transmitter (up to 4). 5.Turn the Ignition OFF to exit programming. The system will also exit programming after 15 seconds of inactivity. Note: This system has 1 button programming which programs all channels of the system. Specifications Condition New 2 button 203no FCC ID GOH-M24 or GOH-MM6-101890 (compatible replacement FCC ID is EZS469 or ESZDEI469) (FCC ID on new style remote is ELVATKC) Part# H7110AS020 Code Alarm, Chapman, Chrysler, Ford, GM, Mitsubishi, Subaru 2 button 314MHz replacement transmitter remote (Control modules with FCC ID: GOH-052-RMTPL, GOH-3YK-BTPRX, GOH-717-JLK) FCC ID: ELVATKC (Replacement for GOH-M24, GOH-M41-014, GOH-MM6-101890) Programmable to the following models: ALLPRO2500, Autobahn, C-350, Chapman-400, Chapman-450, Chapman-500, Chapman-650, CSM2.5, ELITE1100, ELITE1500, ELITE2000SE, ELITE4500, ELITE911, ELITE950, EVS, EVSII, MIRAGE4500, MIRAGE9000, NIGHTHAWK4.0, PRO100, PRO1000, PRO200, PRO3000, PRO3500, PRO750, RCS2, RKE1, SCORPION600, SURESTARTSE, SURESTARTSE433, VSS-200, VSS-250, VSS-350, XTPLUS4.0 Note: Replacement remote you will receive will look slightly different than pictured due to manufacturer changes beyond our control, but will still work and program the same (button configurations can vary on this remote) Note: Will need to use the system's valet switch (programming/override button) to perform the programming procedure, but on some models it is possible to perform programming without the valet switch (access to the receiver under the dash is required) H7110AS021; H7110AS310 Part Number: C-RCX-3 Dealer part # H7110AS020 (H7110AS021; H7110AS310) h7110fs101 Buttons 2: Lock, Unlock Frequency 314 MHz Battery Type 1: GP23A Additional Information This is the replacement remote for systems where the module is found with the FCC ID: GOH-717-JLK & GOH3YK-BTPRX on them. There are other FCC IDs on the module but those always use this remote. This remote was used by many new car dealerships as a dealer installed remote. This means that if a car was not built with factory keyless entry but when the car was ordered as new the customer wanted keyless entry or alarm the dealer ship would install the system that uses this remote. This remote could come with many logos (i.e. ford, chrysler, mitsubishi, subaru, etc...) but they are all made by Code Alarm. The remote comes with programming instructions to make the system accept the remote. _________________________________ Original must look identical... For vehicles manufactured for a U.S. frequency ___________________________________ Programming Instructions: Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. To program transmitters: 1.Turn the ignition ON. 2.Press and hold the valet/override button. 3.Within 10 seconds the system will chirp/flash the parking lights (3) three times, release the button. 4.Press Button 1 of each transmitter you wish to program. The system will respond with 1 chirp for each accepted transmitter (up to 4). 5.Turn the Ignition OFF to exit programming. The system will also exit programming after 15 seconds of inactivity. Note: This system has 1 button programming which programs all channels of the system.